Removed openrov bluetooth disabling stuff to make it mergeable with upstream
This commit is contained in:
parent
c3c2c6dca2
commit
257d05a070
|
@ -1,5 +0,0 @@
|
|||
#!/bin/bash -ex
|
||||
|
||||
install -m 644 files/cmdline.txt ${ROOTFS_DIR}/boot/
|
||||
install -m 644 files/config.txt ${ROOTFS_DIR}/boot/
|
||||
install -m 644 files/interfaces ${ROOTFS_DIR}/etc/network/
|
|
@ -1 +0,0 @@
|
|||
dwc_otg.lpm_enable=0 console=ttyAMA0,115200 console=ttyAMA0,115200 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait
|
|
@ -1,59 +0,0 @@
|
|||
# For more options and information see
|
||||
# http://www.raspberrypi.org/documentation/configuration/config-txt.md
|
||||
# Some settings may impact device functionality. See link above for details
|
||||
|
||||
# uncomment if you get no picture on HDMI for a default "safe" mode
|
||||
#hdmi_safe=1
|
||||
|
||||
# uncomment this if your display has a black border of unused pixels visible
|
||||
# and your display can output without overscan
|
||||
#disable_overscan=1
|
||||
|
||||
# uncomment the following to adjust overscan. Use positive numbers if console
|
||||
# goes off screen, and negative if there is too much border
|
||||
#overscan_left=16
|
||||
#overscan_right=16
|
||||
#overscan_top=16
|
||||
#overscan_bottom=16
|
||||
|
||||
# uncomment to force a console size. By default it will be display's size minus
|
||||
# overscan.
|
||||
#framebuffer_width=1280
|
||||
#framebuffer_height=720
|
||||
|
||||
# uncomment if hdmi display is not detected and composite is being output
|
||||
#hdmi_force_hotplug=1
|
||||
|
||||
# uncomment to force a specific HDMI mode (this will force VGA)
|
||||
#hdmi_group=1
|
||||
#hdmi_mode=1
|
||||
|
||||
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
||||
# DMT (computer monitor) modes
|
||||
#hdmi_drive=2
|
||||
|
||||
# uncomment to increase signal to HDMI, if you have interference, blanking, or
|
||||
# no display
|
||||
#config_hdmi_boost=4
|
||||
|
||||
# uncomment for composite PAL
|
||||
#sdtv_mode=2
|
||||
|
||||
#uncomment to overclock the arm. 700 MHz is the default.
|
||||
#arm_freq=800
|
||||
|
||||
# Uncomment some or all of these to enable the optional hardware interfaces
|
||||
#dtparam=i2c_arm=on
|
||||
#dtparam=i2s=on
|
||||
#dtparam=spi=on
|
||||
|
||||
# Uncomment this to enable the lirc-rpi module
|
||||
#dtoverlay=lirc-rpi
|
||||
|
||||
# Additional overlays and parameters are documented /boot/overlays/README
|
||||
|
||||
# Enable audio (loads snd_bcm2835)
|
||||
dtparam=audio=on
|
||||
|
||||
# Disable bluetooth and move UART back to the original pllc
|
||||
dtoverlay=pi3-disable-bt
|
|
@ -1,11 +0,0 @@
|
|||
auto lo
|
||||
|
||||
iface lo inet loopback
|
||||
iface eth0 inet dhcp
|
||||
|
||||
allow-hotplug eth0
|
||||
iface eth0 inet dhcp
|
||||
metric 0
|
||||
address 192.168.0.100
|
||||
netmask 255.255.255.0
|
||||
gateway 192.168.0.1
|
Loading…
Reference in New Issue
Block a user